At Last, We're Putting Things Back Together
For what seems like an eternity, this Porsche restoration has been about taking things apart.
The engine came out. The cylinder head came off. The crankshaft, pistons, balance shafts, brackets, and just about everything else were removed, inspected, cleaned, repaired, or replaced.
And for weeks, the garage floor seemed to be the preferred storage location for all of it.
But something has finally changed.
We're putting things back together.
When I arrived at the shop, I noticed something different.
Don had taken the time to set up a large table and move most of the parts off the garage floor. What had previously been a collection of boxes, components, and miscellaneous hardware was now spread across a table where we could actually see what we had.
The intake manifold, alternator, A/C compressor, engine brackets, timing covers, balance shaft housings, exhaust components, and dozens of other parts were laid out.
Some had been cleaned and refinished. Others were still waiting their turn. And there were plenty of new parts mixed in with the old.
At least now we had a better idea of what was there and where to find it.
It may not sound like much, but after weeks of disassembly, seeing everything organized felt like progress.
The next surprise was the workbench.
Don had cleared it and arranged the major engine components in preparation for reassembly.
The freshly machined cylinder head was there, along with the camshaft, pistons, connecting rods, bearings, and other components that would eventually find their way back into the engine.
The machine shop had returned the replacement block, my original cylinder head, and the other components we'd sent out.
After the setbacks with the original cracked block and the unsuccessful search for a suitable replacement, it was encouraging to see everything ready to go.
The replacement block was the one Don had kept in storage for approximately 15 years. After rejecting the other candidates, Bill and Don had inspected this one and agreed it was a good foundation for the rebuild.
Now we were finally getting somewhere.

The workbench is cleared, the parts are laid out, and the rebuild is finally underway
And then there was the engine itself.
Don had mounted the replacement block on the engine stand and had already begun installing the crankshaft.
One important detail: this wasn't a crankshaft from the replacement engine.
It was the original crankshaft from my 1984 Porsche 944.
We had sent it to the machine shop to be checked and fitted to the replacement block. The goal was to retain the original crankshaft, provided it was suitable, while using new bearings and the replacement block.
When I arrived, Don was particularly pleased with the results.
He wanted to show me something.
Rather than reaching for a wrench to rotate the crankshaft, he simply turned it by hand.
It moved smoothly.
Don explained that being able to rotate the crankshaft so easily was an encouraging indication of how well the crankshaft and new bearings were fitting together.
He was clearly proud of the work, and I could understand why.
After all the problems we'd encountered with the original engine, seeing that crankshaft turning freely inside the replacement block was a pretty satisfying moment.
Of course, there's still a long way to go before this engine runs again, but this was the first real sign that we were building something rather than taking something apart.
My original crankshaft, now installed in the replacement block with new bearings. Don was pleased that it turned smoothly by hand.
Another piece of good news was finally being able to confirm the engine serial number on the replacement block.
Engine Serial Number: 4308903
With the block cleaned and accessible, we could clearly identify the stamped number.
It might seem like a small detail, but documenting the engine's identity is important to me, especially since this is no longer the original block that came with the car.
The replacement block came from Don's long-stored spare engine, while the crankshaft and cylinder head are from my original engine.
I want to keep an accurate record of what went into this rebuild, both for the restoration history and for whoever might be working on this Porsche years from now.
Replacement engine serial number 4308903. Another important detail documented for the restoration record.
While Don was getting started on the engine reassembly, I managed to finish another project that had been occupying quite a bit of my time.
The engine bay.
With the engine removed, I'd taken advantage of the opportunity to clean up years of accumulated grime, address areas of surface rust, and touch up the paint.
A few days earlier, I'd applied the base coat in the original M3V deep burgundy. The results were encouraging, but there was still one final step: the clear coat.
Bill had offered to let me use his high-heat clear coat rather than the standard automotive clear I'd originally planned to use.
He also reminded me that humidity matters when painting, particularly when applying clear coat.
With rain in the forecast, I decided to wait for better conditions.
Today, I finally got the clear coat applied.
Once it was finished, I removed all the masking paper and tape that had been protecting the surrounding components.
And there it was.
For the first time since we'd removed the engine, the engine bay was beginning to look like something ready to be put back together rather than taken apart.
It's certainly not a professional, bare-metal restoration, nor was that ever the intention. My goal was to preserve as much of the original finish as possible, address the problem areas, and make everything look presentable before the engine went back in.
I'm pleased with how it turned out.
There's still some work to be done, including the rust repairs around the battery-box drain and passenger-side inner fender. But another substantial piece of the project is behind me.
And I have to give Bill credit. He's been generous with both his supplies and his knowledge, and I continue to learn something new every time I'm at the shop.
Fresh M3V burgundy paint, clear coat applied, and masking removed. Not a concours restoration, but a tremendous improvement over what we started with.
Earlier in the week, Don had suggested that I consider replacing some of the more visible bolts, nuts, and washers with freshly yellow-zinc-plated hardware. After spending so much time cleaning and refinishing the engine components, it made sense. The old hardware would certainly stand out against everything else.
So I started searching online.
And, as seems to be the case with anything Porsche-related, I quickly discovered just how expensive a handful of bolts and washers could become.
Then I remembered that Don had mentioned a local Porsche 944 parts dealer named Josh Bare. Josh dismantles 944s and has much of the hardware, brackets, and other metal components replated before offering them for sale.
I reached out to him, and we arranged to meet at his warehouse on Saturday morning.
At 8:00 a.m., I arrived to find Josh ready to help.
He brought out several bags filled with bolts, washers, nuts, brackets, tensioners, and other miscellaneous Porsche hardware and began spreading everything across a long table.
Interestingly, the table also had a collection of old plates and dishes on it.
Josh explained that someone was on their way to pick them up. Apparently, he's also gotten into buying abandoned storage units.
Naturally, I asked whether he was planning to appear on the television show Storage Wars.
He laughed.
My Saturday morning haul from Josh Bare. All of this freshly plated Porsche hardware and assorted parts for $100.
Along one wall of the warehouse was a shelving system filled with bins, each labeled with the type of parts inside. Josh started going through them as we talked about what I needed.
One item on my list was a replacement air-oil separator (AOS). During the engine work, Don had been trying to fit my original AOS when the lower lip cracked, leaving me in need of another one.
Then there were the bolts.
Josh had about five different hardware organizers, and every time I asked about a particular fastener, he'd walk over to one of them and return with a freshly plated example.
It was certainly easier than trying to identify and order every individual bolt online.
I also found a bag containing the power steering pump mounting bracket, pulley, and associated hardware.
Since I'd already rebuilt my original ZF power steering pump, these were perfect additions. I pulled out the pieces I needed and planned to install them on the rebuilt pump when I returned to the shop the following week.
By the time we finished, I'd collected quite an assortment of freshly plated hardware, brackets, and other pieces.
The total cost?
$100.
Considering what I'd been seeing online, I was pretty pleased with myself.
And I had to admit, Don was right. That yellow-zinc finish was going to look great against the cleaned aluminum and freshly painted engine components.
After leaving Josh's warehouse, I headed over to the shop to drop off my morning's purchases.
Don was there, and I showed him everything I'd found. He was happy with the selection, particularly since this whole adventure had started with his suggestion that I look into replacing some of the visible hardware.
My plan was pretty simple.
Drop off the parts, head home, get Mala and Thor, and spend the afternoon walking around Piedmont Park.
But Don had other ideas.
After looking over the hardware, he casually asked:
"So, what are you working on today?"
Well, that wasn't exactly what I had in mind.
I'd only planned on dropping off the parts.
But standing there, I realized I probably wasn't going to get away without doing something.
I needed to think quickly.
Fortunately, I still had those rusted areas in the engine bay that needed attention.
Earlier in the week, Elliott had brought me a large section of original sheet metal he'd cut from another 1984 Porsche 944. He'd removed the entire battery-tray corner, along with some additional surrounding metal, so I'd have enough material to repair the rust around my battery-tray drip tube and inner fender.
I'd already cut out the individual replacement pieces I thought I needed, but I still had to remove the damaged metal from my car and check the fit.
So I decided that would be my project for the day.
I cut out the two rusted sections, taking care to work around the surrounding metal, and then brought over the replacement patches I'd cut from Elliott's donor panel.
The good news was that they fit.
And because the metal came from another 1984 944, the original curves and contours were already there. That saved me from having to fabricate the patches from scratch.
By the time I finished, both damaged sections had been removed and the replacement pieces checked for fit.
Not bad for a Saturday when I hadn't planned on doing any work at all.
Test-fitting one of the replacement pieces cut from the original 1984 Porsche 944 donor section Elliott supplied earlier in the week.
Fortunately, I still managed to get home in time.
Mala and I got Thor loaded into the car, and we headed down to Piedmont Park as originally planned.
We walked 2.5 miles, and Thor got to spend some time playing at the dog park before we left.
From there, we headed to Mellow Mushroom for dinner.
They have an outdoor patio that welcomes dogs, and we've been taking Thor there since he was about a year old.
Now, at 6½ years old, he knows the place pretty well.
And more importantly, he knows exactly what happens when we go there.
Pizza crust.
He's learned that if he waits patiently, sooner or later someone is going to share a little crust with him.
So Saturday turned out to be a pretty good day after all.
I picked up a great collection of freshly plated Porsche hardware for $100, made some unexpected progress on the rust repairs, got a 2.5-mile walk in with Mala and Thor, and finished the evening with pizza.
And Thor got his crust.
I'd call that a successful Saturday.
On Monday, I returned to the shop to get the patches installed.
I used 3M automotive panel adhesive between the overlapping metal surfaces and secured the patches with rivets. Once everything was in place, I sprayed the repaired areas with Eastwood Red Oxide Primer.
The patches are now installed, and I'm pretty happy with how they turned out.
There's still some finishing work ahead. I've ordered 3M automotive seam sealer to seal the edges and rivets. Once that's done, I'll spray the repaired areas in M3V burgundy to match the rest of the engine bay.
It's nice to have these two rusted areas behind me, or at least almost behind me.
And thanks to Elliott, the repairs were made using original Porsche sheet metal from another 1984 944.
Now, back to getting everything ready for Don's engine.
Both patches installed with panel adhesive and rivets, then coated with Eastwood Red Oxide Primer. Seam sealer and M3V paint are still to come.
For much of this restoration, progress has been measured by what we've discovered, removed, repaired, or replaced.
Cracked blocks. Worn gaskets. Sludge. Rust. And more than a few unexpected expenses.
Now, for the first time in a while, progress is being measured by things going back together.
The engine parts are organized. The replacement block is on the stand. My original crankshaft is installed and turning smoothly. The engine bay has fresh paint and clear coat. And we're beginning to pay attention to the smaller details that will make the finished result that much better.
There's still plenty to do.
But the direction has finally changed.
We're no longer taking the Porsche apart. We're putting it back together.
And that feels pretty good.
Back at Don's shop, things are finally starting to come together.
The cylinder head is in place, the balance shaft housings are going back on, and the collection of parts that had been spread across the workbench is beginning to resemble an actual Porsche engine.
The yellow-zinc hardware I picked up from Josh Bare is already making a difference. It may seem like a small detail, but after spending so much time cleaning and refinishing everything, I really didn't want to put it all back together with 40-year-old rusty bolts.
Don has been steadily working through the assembly, and I took a few pictures and videos while he was at it. There's something satisfying about watching all these pieces go back together, particularly after everything we've been through trying to find a usable engine block.
The next time I stopped by, Don had made even more progress.
The cam tower was installed, complete with that big PORSCHE lettering across the top. After seeing the engine in pieces for so long, that alone was a pretty satisfying sight.
And the stainless exhaust header I'd purchased earlier was finally mounted. The original ceramic coating had chipped during shipping, so rather than return it, I refinished the header myself using VHT FlameProof Aluminum and baked it according to the manufacturer's curing instructions.
I was hoping the aluminum finish would stand out against the freshly cleaned engine, and seeing it installed, I'm glad I went that route. It looks terrific.
Between the cleaned aluminum castings, yellow-zinc hardware, and refinished exhaust header, everything is starting to come together. Don's doing a great job bringing this engine back to life.
There are still plenty of components to install before the engine is ready to go back into the car, but the difference from just a few days ago is remarkable.
For the first time in a while, I'm looking at something that resembles a finished engine rather than another expensive collection of Porsche parts.
And I have Don to thank for that.
While looking over the engine, I found a casting date marking that appears to read February 1982.
That's interesting because this engine is going into my 1984 944. Don had this engine stored for roughly 15 years, and until now, I hadn't given much thought to just how early the block might be.
It may also explain another little problem we've encountered. The air-oil separator from my original engine doesn't fit the replacement block properly. Apparently, Porsche made some changes to the separator and its mounting arrangement during the early production years. We're still working out exactly which version this block requires.
Naturally, even the replacement engine has found a way to introduce another parts challenge.
At least this time we're dealing with a fitting issue rather than another cracked or unusable engine block. I'll take that trade.
One of the things still keeping the engine from being finished is the oil pan.
Don convinced me to spend another $111.68 on a Lindsay Racing modification that adds a small hinged flap inside the pan. The idea is to help keep oil around the pickup tube during hard cornering, rather than letting it slosh away when the car is being pushed through a turn.
Will I ever drive this car hard enough to need it? Maybe. But after everything we've been through with this engine, a little extra protection seemed like a reasonable investment.
Don sent the oil pan to a friend who's welding the modification into place, so we're waiting for it to come back.
There's a funny side to this, too. Don liked the design enough that he's using the part I purchased as a template to make similar modifications to his own oil pans.
Apparently, my Porsche restoration has now become a research and development project for Don.
Another $100 added to the restoration ledger.
At least this time, I know exactly what the money is supposed to accomplish.
Another productive day at the shop, and I think I can finally say the engine bay is ready for Don to return the engine to its rightful place.
Today I finished up the rust repairs by applying seam sealer, followed by a little more M3V burgundy paint to finish everything off. After giving it time to set up, I installed the firewall insulation.
Next came the cleaned bellhousing, which is now back in place. I also replaced the last exhaust hanger, which hadn't been included in the original replacement kit.
Nothing particularly exciting about any of those individual jobs, but collectively they represent quite a bit of work. Between repairing the rust, refinishing the engine bay, installing the insulation, and getting everything cleaned up, this part of the restoration has taken considerably more time than I originally anticipated.
Looking at the engine bay now, it's hard to believe how much has changed since we pulled the engine in October.
And for once, I'm not looking at a list of things I still need to take apart.
Now we just need Don to finish building the engine so we can put something back into that big empty space.
While I've been working on getting the engine bay ready, Don has been making some serious progress on the engine itself.
The cam tower is installed, the balance shaft housings are back in place, and the timing and balance shaft belts are fitted. The oil filter and several other components have also found their way back onto the engine.
And then there's the exhaust header.
When it arrived, the ceramic coating had been damaged during shipping. Rather than return it, I refinished it myself using VHT FlameProof Aluminum and baked it according to the manufacturer's curing instructions. Seeing it mounted on the engine, I'm really happy with that decision.
Between the cleaned aluminum castings, the yellow-zinc hardware, and the silver header, the engine is looking better than I could have imagined when we started this adventure.
Of course, there are still a few things to finish. We're working through the issue with the air-oil separator on the February 1982 engine block, and the intake manifold and remaining accessories still need to be installed.
But looking at these pictures, it's getting harder to remember the filthy, sludge-covered engine that started this whole process.
Don is doing a fantastic job, and I'm getting pretty excited about seeing this engine back where it belongs.
Of course, it wouldn't be a Porsche restoration without another unexpected complication.
As Don was putting the engine back together, we discovered that the air-oil separator (AOS) from my original 1984 engine wouldn't fit the replacement block.
Remember, this replacement block was cast in February 1982. Apparently, Porsche made a change to the AOS mounting arrangement on the early engines. The lower connection on the 1982 block is approximately 4 mm smaller than the one on my original engine.
That meant I needed an early AOS, Porsche part number 944 107 180 06, rather than the later 944 107 180 08.
Simple enough, right? Just order one.
Not quite.
The 944 wasn't introduced in the United States until the 1983 model year, so finding a part specific to a 1982 engine in the U.S. was going to be a challenge.
Mark Plieman at Plyhammer Parts suggested I expand my search to Europe, where the 944 had been available in 1982. That sent me down another rabbit hole, contacting Porsche dismantlers and parts suppliers in Germany, the Netherlands, and the United Kingdom. I even looked into Australia.
With a little help from Google Translate and ChatGPT, I started sending inquiries in German and Dutch, hoping someone had one of these early separators sitting on a shelf.
Eventually, I connected with Bernd in Germany.
And that's when my Porsche restoration took an unexpected turn into international correspondence.
Bernd wrote:
“Hallo Jeff. Nachher schicke ich das Foto, versenden kann ich das erst morgen aber dann sind die Dichtringe nicht dabei, die wollte ich noch bei Porsche kaufen. Kannst du das mit PayPal bezahlen?”
Which roughly translates to:
“Hi Jeff. I'll send the photo later. I can't ship it until tomorrow, but the sealing rings won't be included. I was planning to buy those from Porsche. Can you pay with PayPal?”
Not exactly the sort of German I expected to be learning when I bought this car.
And the price? 30 euros.
For perspective, I'd found a new early separator advertised for roughly €550. Suddenly, my international parts hunt was looking like a pretty good investment.
I responded:
“Ich weiß es wirklich zu schätzen, dass du dir so viel Mühe gibst, das Teil so schnell wie möglich auf den Weg zu bringen.”
Or, in English:
“I really appreciate you going to so much trouble to get the part on its way as quickly as possible.”
As I write this, we're still working through the final details of getting the part shipped to Atlanta. Hopefully, by the time Don is ready for it, the separator will have completed its transatlantic journey.
One more reminder that restoring a 42-year-old Porsche isn't always about turning wrenches. Sometimes it's about finding the right person halfway around the world who happens to have exactly what you need.
And apparently, learning a little German along the way.
Another productive day at the shop, and I think I can finally say the engine bay is ready for Don to return the engine to its rightful place.
Today I finished up the rust repairs by applying seam sealer, followed by a little more M3V burgundy paint to finish everything off. After giving it time to set up, I installed the firewall insulation.
Next came the cleaned bellhousing, which is now back in place. I also replaced the last exhaust hanger, which hadn't been included in the original replacement kit.
There was one final loose end — the A/C line.
At some point, someone had cut the original rubber hose to install an additional service fitting when the system was converted to R134a. I wanted to eliminate that fitting, but replacing the entire line would have meant dealing with the metal tubing that runs through the firewall and under the dashboard.
Fortunately, Bill had a six-point A/C hose crimping tool. With a replacement hose and a new ferrule, we were able to make the connection without tearing apart the rest of the system.
One more item off the list.
Between the rust repairs, refinished engine bay, firewall insulation, cleaned bellhousing, exhaust hanger, and now the A/C line, I've finally run out of things I need to do before the engine goes back in.
I'm sure I'll find something else eventually. It's a Porsche, after all.
But for now, the engine bay is ready.
Don, whenever you're ready, I've got a place for that engine.
The last loose end: a newly crimped A/C hose connection, courtesy of Bill's six-point crimping tool. No need to replace the entire line through the firewall.
Stopped by the shop again, and the engine is looking more complete every time I see it.
The intake manifold is back on, along with the fuel rail, injectors, throttle body, and much of the plumbing and wiring. The timing covers are installed, and the engine is starting to look like the one that came out of the car — only considerably cleaner.
Seeing the silver exhaust header alongside the cleaned aluminum intake manifold and cam tower, I'm really pleased with how everything is coming together.
Don is getting close to the point where he can take the engine off the stand and prepare it for installation.
Meanwhile, the engine bay is finished and waiting.
After all the setbacks with the original block, the search for a replacement, and the unexpected parts hunt for the early-1982 air-oil separator, it's exciting to finally be talking about putting an engine back into the car.
We're not quite there yet, but we're getting close.
