Tools & Restoration Products

When I purchased my 1984 Porsche 944, I knew there would be some mechanical work involved. What I hadn't fully appreciated was how much time I'd spend cleaning, removing rust, refinishing parts, and figuring out which products actually worked.

Over the course of the restoration, I've accumulated a collection of tools, chemicals, paints, adhesives, and other supplies that I probably wouldn't have considered buying a few years ago.

Some have been excellent. Others have required a little trial and error.

This isn't intended to be a comprehensive list of everything I've purchased. These are some of the products and tools that have been particularly useful along the way.

Cleaning & Rust Removal

Evapo-Rust — Rust Remover

Status: Used

Manufacturer website

Evapo-Rust has become one of my favorite products for restoring old metal components.

I've used it on various parts, including the front suspension knuckles, to remove years of surface rust without having to aggressively grind or sand the metal.

The process is fairly simple: clean off the heavy grease and dirt, submerge the part, and let the solution do its work.

Some of the suspension components spent approximately 13 hours soaking.

The results were impressive, although I learned that freshly cleaned bare metal needs to be dried and protected fairly quickly. Otherwise, surface rust can start returning.

For parts that can be removed and submerged, this has been one of the most useful products in the restoration.

Dura-Coating Wheely Clean

Status: Used

This has been another useful cleaning product, particularly when dealing with accumulated brake dust and grime on wheels and other suitable surfaces.

One thing I've learned is that getting parts properly cleaned before refinishing them often takes longer than the painting itself.

Rust Protection & Refinishing

Eastwood Red Oxide Rust Encapsulator Plus

Status: Used

Manufacturer website

I selected Eastwood's Red Oxide Rust Encapsulator Plus for areas where I wanted additional protection against corrosion.

The battery tray and surrounding engine-bay sheet metal required particular attention because of the rust and water damage I discovered during the restoration.

After removing damaged metal and preparing the repair areas, corrosion protection became an important part of the process.

My goal wasn't simply to make the engine bay look better. I wanted to reduce the likelihood of having to deal with the same rust again.

Eastwood Extreme Chassis Black — Satin

Status: Used

Manufacturer website

I used Eastwood's Extreme Chassis Black Satin as part of the refinishing work on suspension and other appropriate metal components.

I wanted a durable, relatively understated finish rather than something excessively glossy.

The satin black finish provides a clean appearance while keeping the parts looking reasonably close to their original character.

VHT FlameProof — Aluminum

Status: Purchased for header refinishing

Manufacturer website

The stainless-steel exhaust header I purchased arrived with a ceramic coating that had been chipped during shipping.

Rather than return the header, I decided to refinish it.

After preparing the damaged coating, I selected VHT FlameProof Aluminum to provide a consistent finish across the header.

Bill suggested aluminum rather than trying to duplicate the original bronze-colored coating, partly because the lighter finish would stand out nicely against the deep burgundy engine bay.

As with any high-temperature coating, proper preparation and curing are important.

Sheet Metal Repair & Adhesives

3M Automotive Panel Bonding Adhesive

Status: Used

Manufacturer website

The rust repairs around the battery tray and inner fender introduced me to another category of restoration products: automotive panel adhesives.

Elliott at 944Barn supplied original sheet metal cut from a donor 1984 Porsche 944. I then cut and fitted the replacement patches to repair the damaged areas.

I selected 3M Automotive Panel Bonding Adhesive for the patch work, along with mechanical fastening where appropriate.

It provided an alternative to welding in areas where access and heat were concerns.

As with any sheet metal repair, the suitability of adhesive depends on the location and whether the panel is structural.

3M Ultrapro Autobody Sealant — 08301

Status: Used

Manufacturer website

After the metal repairs, seam sealing was another important step.

I used 3M Ultrapro Autobody Sealant to help seal repaired joints and prevent water from finding its way back into areas that had already suffered corrosion.

Given the amount of water intrusion I discovered when I first

Heat Protection & Insulation

DEI Floor & Tunnel Shield II

Status: Used — Preferred product

Manufacturer website

With the engine removed, I had an opportunity to address the insulation and heat protection around the firewall and transmission tunnel.

I purchased DEI Floor & Tunnel Shield II for this work, and it turned out to be the better choice for my application.

The material was easier to work with for the areas I wanted to cover, and I preferred the way it fit and conformed to the surfaces.

After comparing it with another DEI heat shield product, this is the one I decided to use.

DEI Adapt-A-Shield XT

Status: Purchased — Not installed

Manufacturer website

I also purchased DEI Adapt-A-Shield XT, a flexible aluminum heat barrier, with the idea of adding extra protection near the exhaust manifold.

After working with the Floor & Tunnel Shield II, however, I'm not convinced I'll need the Adapt-A-Shield.

The Floor & Tunnel Shield was a better fit for what I was trying to accomplish.

For now, the Adapt-A-Shield is sitting on the shelf. I may find another use for it, but I'm not going to install something simply because I already bought it.

Boom Mat Black Under Hood Thermal Acoustic Lining

Status: Used — Bell housing insulation

Manufacturer website

Another product I purchased was Boom Mat Black Under Hood Thermal Acoustic Lining.

Although it's marketed primarily for use beneath the hood, I used it around the bell housing as part of the insulation work.

This was another area where I wanted to improve the insulation while the engine and surrounding components were removed and access was considerably easier.

The black finish also worked well with the surrounding components.

DEI Heat-Resistant Tape

Status: Used

Manufacturer website

I used DEI black heat-resistant tape around the edges of the firewall insulation.

The tape worked well across the flat surfaces, although getting it to stay adhered where it wrapped around certain edges proved more challenging.

That led to some additional experimentation with high-temperature adhesives.

Another reminder that a product can work perfectly well in one application and be less cooperative in another.

Specialty Tools

Tie Rod End Removal Tool

Status: Used — Worked very well

Purchased from: Amazon — Tie Rod End Removal Tool

While rebuilding the steering system and refreshing the front suspension, I needed to separate the tie rod ends from the steering knuckles.

I purchased this dedicated removal tool through Amazon, and it worked very well.

It made separating the tie rod ends much easier without having to resort to hammering on the surrounding components.

One of those relatively inexpensive specialty tools that was well worth having for the job.

Orion Motor Tech MacPherson Strut Spring Compressor

Status: Purchased for front strut disassembly

Purchased from: Amazon — Spring Compressor

Manufacturer: Orion Motor Tech

Disassembling the front struts required compressing the coil springs so the upper mounts could be removed safely.

I purchased this Orion Motor Tech spring compressor set through Amazon for the job.

The springs were eventually sent out for powder coating in a Koni-inspired yellow, while I cleaned and refinished the remaining suspension components.

Spring compressors are one tool I approach with considerable respect. There is a lot of stored energy in a compressed spring, and using the correct equipment and procedures is essential.

Bernzomatic MAP-Pro Torch

Status: Owned — Evaluated for metal repair

Manufacturer website

I already had a Bernzomatic MAP-Pro torch, which became part of my investigation into possible approaches for small metal repairs.

One of the things this project has taught me is that having a tool doesn't necessarily mean it's the right tool for every job.

Understanding the limitations of the equipment is just as important as knowing how to use it.

A Few Lessons Learned

If there's one recurring lesson from the cleaning and refinishing work, it's that preparation makes an enormous difference.

Removing rust is only part of the job. The metal needs to be cleaned, dried, prepared, and protected before corrosion has an opportunity to return.

I've also learned that products marketed for similar purposes aren't necessarily interchangeable. Paints, primers, adhesives, sealants, and heat barriers all have their own requirements and limitations.

The DEI heat shielding was a good example. I purchased two different products for essentially the same problem, but after working with them, I found that one was much better suited to my needs.

And sometimes the best solution is simply to ask someone who's done the job before.

That's been a recurring theme throughout this restoration, and probably one of the reasons I've managed to get as far as I have.

NOTE:

These are products and tools I've purchased, used, or evaluated during my personal restoration. Some applications are still in progress, and inclusion here should not be taken as a recommendation for every repair. There are no paid endorsements or sponsorships.