While we wait

While We Wait…

Third Time's the Charm?

After discovering the poorly repaired weld on the original engine block, we were right back where we'd started.

We needed another engine block.

It was around 5:00 Tuesday afternoon when Don mentioned that he had an old 944 engine sitting in his storage unit. It had been there for something like 15 years. At one point, he'd even considered getting rid of it, but for whatever reason, he'd left it alone.

That was encouraging, but I wasn't about to put all my eggs in one basket.

So I went home and started searching.

Facebook Marketplace, Google, social media groups, classified listings. You name it, I probably looked there.

Around 9:00 that evening, I found a listing in Austell, Georgia, for a Porsche 944 short block. The asking price was $400.

I contacted the seller, Tim G., and he sent me some additional photographs. From what I could see, the block looked promising.

We kept chatting, and it turned out he lived only about three miles from me. Another local 944 enthusiast, and someone I was looking forward to meeting.

I arranged to pick up the block at 9:00 Wednesday morning. Tim agreed to let me have it inspected with a $100 deposit.

By 9:30, I had it down at the shop for Bill and Don to examine.

Not bad for something I'd only discovered the night before.

Don took the first look and seemed pretty encouraged.

Then Bill came over.

By now, I was learning that when Bill examines an engine block, he knows exactly where to look.

He went straight to cylinder #4, near the top of the cylinder wall on the thrust side, and started running his fingernail up and down the surface.

Something didn't feel quite right.

A little cleaning, another pass with the fingernail, and there it was.

Pitting.

A small amount of scoring might have been acceptable, but pitting in the cylinder wall was another matter entirely.

Bill wasn't comfortable using the block.

And just like that, another promising candidate was off the list.

I loaded the short block back into the 4Runner and headed over to Tim's. He returned my $100 deposit, no problem.

I was disappointed, of course, but at least we'd found the problem before spending money on machine work or rebuilding an engine that wasn't worth rebuilding.

And I'd made the acquaintance of another local 944 enthusiast along the way.

Not a total loss.

The Engine That Almost Got Thrown Away

Which brought us back to Don.

Remember that engine he'd mentioned sitting in storage for 15 years?

Well, now it was time to go get it.

Bill sent Don to retrieve it, and once it was back at the shop, Don began taking it apart so they could inspect what we had.

Given our recent track record with replacement engines, I wasn't getting my hopes up just yet.

But this time, things were different.

Don broke it down, and both he and Bill gave it a thorough inspection.

Finally, we had a winner.

The engine that had been sitting in storage for 15 years—the one Don had nearly gotten rid of—turned out to be a very good foundation for our rebuild.

After everything we'd been through trying to find a usable block, the solution had been sitting in Don's storage unit all along.

The block, cylinder head, and cam tower were headed to the machine shop for cleaning and machining.

We were told to expect at least a three-week turnaround.

And that left me with a question.

What was I supposed to do for the next three weeks?

As it turns out, plenty.

A $50 Power Steering Pump

I'd already rebuilt the power steering rack, but the pump still needed some attention.

One corner of the pump housing was broken. It wasn't something a new seal kit was going to fix, and my first thought was to call Elliott and see about getting a replacement.

But before I did that, I decided to do a little research.

The pump was a ZF unit, and I discovered that it could be disassembled and refurbished with new seals and a shaft bearing. That took care of the mechanical side of things, but I still needed to address the broken housing.

Then I found something interesting on eBay.

Someone was selling a used power steering pump that also had a broken housing. The difference was that the damage was on the bottom half, while the top half was still good.

Exactly the opposite of my problem.

And the price?

$26.

I ordered it, along with a seal and bearing kit from 944online for about $12.

Between the two pumps, I had the pieces I needed to make one good unit.

After cleaning everything, replacing the seals and bearing, and reassembling the pump, I had a refurbished power steering pump for less than $50.

Not bad, considering I was originally thinking about buying another complete pump.

And I have to admit, there was something particularly satisfying about taking two broken pumps and turning them into one good one.

Bringing the Restoration Home

With the power steering pump finished, I started looking for other things I could work on while the engine was away.

One of the advantages of having the engine removed from underneath the car was that so much of the front suspension and subframe had already been disassembled.

There were parts everywhere that could benefit from a good cleaning and refinishing.

And I had a plan.

I tend to get up pretty early in the morning. Rather than driving over to the shop every time I wanted to work on something, why not bring some of the smaller projects home?

I had my tools, a place to work, and plenty of time before the engine came back.

So that's exactly what I did.

First came the engine crossmember.

After more than 40 years, it had accumulated its share of grease, dirt, and surface rust. I cleaned it up, addressed the corrosion, and started getting it ready for refinishing.

Next came the engine mounting arms and other pieces of the front subframe.

One by one, parts started making their way from Don's shop to my garage.

It was almost like having a second restoration project going on at home.

The Alternator, the A/C Compressor, and Everything Else

Don also gave me the alternator to clean.

And it needed it.

The aluminum housing was heavily oxidized, and while the alternator itself wasn't necessarily in need of replacement, it certainly looked like it had spent the last four decades under the hood.

So that became another cleaning project.

Then, while spending some time cleaning the engine bay, I noticed just how filthy the air-conditioning compressor was.

With everything else getting cleaned up, it seemed a shame to leave that sitting there covered in years of grime.

Off it came.

And home it went.

Superscript

Apparently, Clean Isn't Always Clean Enough

I thought I was making pretty good progress cleaning up the various components that had come off the car.

Then Don took another look at my work.

We were discussing the oil pan, which I thought looked pretty good. After all, I had already spent considerable time cleaning out the awful sludge we discovered when the engine came apart.

But looking at it more closely, there were still areas of discoloration, and the aluminum wasn't quite as clean as I would have liked.

I mentioned this to Don.

He looked at it and said, "Well, it's really up to what you want... but I've seen these shine like a mirror."

Thanks, Don.

Now, I know he wasn't criticizing my work. He was simply pointing out what was possible. But once someone tells you that a part can shine like a mirror, it's awfully difficult to look at your own work and say, "Good enough."

So, the oil pan came home with me.

And while we were discussing that, Don reminded me that the bellhousing was only held on by four bolts.

I had already spent time cleaning the underside of the housing while it was still attached to the torque tube. I had done what I could reach, and it looked considerably better than when I started.

But, of course, there was still the top.

"Take the four bolts out," Don suggested, "and you can get the top just as clean as the bottom."

Well, when he put it that way...

So the bellhousing came home, too.

At this point, I'm beginning to wonder whether Don realizes that I actually have a house and a life outside of cleaning Porsche parts.

But he has a point.

With the engine out, the transmission components accessible, and everything apart, this is probably the only opportunity I'll have to get these pieces looking the way I really want them.

And the difference is remarkable. Forty-plus years of accumulated dirt, oxidation, and grime are slowly giving way to clean aluminum.

The oil pan is looking better than I ever expected, and the bellhousing is finally getting the attention that the inaccessible areas never could have received while installed.

I'm also learning something about restoration.

There's a big difference between getting something clean enough to put back together and getting it clean enough that you're proud to put it back together.

Apparently, Don intends to make sure I understand that distinction.

And then I looked at the front strut assemblies.

Both of them.

They were already off the car, and after seeing how well some of the other components were cleaning up, I figured I might as well give them the same treatment.

So the left and right strut assemblies came home, too.

At this point, I'm not entirely sure whether I'm restoring a Porsche at Don's shop or slowly relocating it to my garage.

Probably a little of both.

And to think, this all started because I needed something to do while waiting three weeks for the machine shop.

A little Koni yellow. 

The original front springs are back from powder coating, and the spring compressors are in place for reassembly. I'm keeping the factory spring setup and ride height, but giving the entire assembly a much-needed refresh.

A Little Garage Ingenuity

With the strut housings and steering knuckles cleaned and refinished, it was finally time to start putting everything back together.

Of course, assembling a front strut, control arm, and brake components on the garage floor isn't particularly convenient.

So I found another use for a piece of 6×6 lumber.

I cut a couple of sections to serve as makeshift assembly stands, giving me a way to support the suspension components while I worked.

Nothing fancy. Just a little garage ingenuity.

But it worked.

And with both assemblies taking shape, I could finally see the results of all those early mornings spent cleaning, removing rust, painting, and refurbishing parts.

There was something satisfying about looking at the finished components and knowing that, not long ago, they'd been covered in 40 years of dirt and grime.

Sometimes the best tool in the garage isn't something you buy. It's something you make.

Back to German Automotive

With both front suspension assemblies finally completed, it was time to load them up and return them to German Automotive.

After all the disassembly, rust removal, cleaning, painting, powder coating, and reassembly, it was satisfying to see them standing side by side at the shop.

The original springs, now finished in Koni yellow, really stand out against the freshly refinished black strut housings and brake components.

I have to admit, I'm pretty proud of how these turned out.

What started as another project to tackle while waiting for the engine has become one of the more satisfying parts of the restoration.

Now Bill and Don can take over the installation.

And with the engine components also back from the machine shop, we're finally reaching the point where parts are going back onto the car instead of coming off it.

That's progress!

A Little Good News from the Machine Shop

Well, the first piece is back from the machine shop.

And it's actually a piece of my original engine.

We decided to reuse the original cylinder head, and after all the carbon buildup, deteriorated head gasket, and other surprises we found during the teardown, it was pretty remarkable to see it looking almost new again.

The head has been cleaned and resurfaced, and apparently all eight valves have been replaced.

Considering that this entire engine adventure started with cylinder #4 having only 40 PSI of compression, seeing the cylinder head back in this condition feels like real progress.

The replacement block and cam tower are still at the machine shop, so we're not quite ready to start putting everything back together.

But after months of setbacks, I'll happily take a little good news.

One piece down. Two more to go.

Jackpot! The Machine Shop Delivers

Finally, some really good news.

After everything we've been through trying to find a usable engine block, the waiting is over. All the major components are back from the machine shop.

And they look fantastic.

The cylinder head, cam tower, crankshaft, flywheel, and replacement engine block have all returned, cleaned and machined, and are ready for the next stage of the rebuild.

Seeing the cylinder head and cam tower laid out together was particularly satisfying. The aluminum looks almost new, and the PORSCHE lettering on the cam tower really stands out.

The flywheel has a freshly machined surface, the crankshaft is back, and the replacement block looks promising.

Considering where this adventure started—with only 40 PSI of compression in cylinder #4, a failed head gasket, an unbelievable amount of sludge, and eventually the discovery that the original block had been cracked and repaired—this feels like a significant turning point.

Then there was the search for a replacement block. One engine had corrosion problems, another had pitting in cylinder #4, and for a while it seemed as though every potential solution came with another disappointment.

Fortunately, Don had an engine tucked away in storage for approximately fifteen years.

Who would have guessed that the answer was sitting there all along?

Now, after the machine-shop work, we finally have the major pieces needed to begin putting an engine back together.

Of course, there's still plenty of work ahead. Don and Bill have the actual engine assembly to tackle, and I still have several projects underway in the engine bay.

But for the first time in a while, we're moving toward putting things back together rather than taking them apart.

And that feels pretty darn good.

While the Engine Was Away...

When Bill and Don decided to remove the engine from underneath the car, I wasn't entirely convinced it was the most economical approach.

But now, looking at the empty engine bay, I was beginning to appreciate the benefits.

With the engine, crossmember, and front suspension out of the way, I had access to places that probably hadn't seen daylight since the car left the factory.

And after 42 years, they certainly needed some attention.

I started by addressing the firewall insulation. The old material had deteriorated, so this was an opportunity to replace it while everything was accessible.

Then came the rust.

There were several areas where moisture and time had taken their toll, particularly around the battery tray and adjoining sections of the engine bay.

Of course, nothing is quite as simple as spraying on a little paint.

First came the cleaning, then removing loose rust and deteriorated coatings, followed by carefully masking the hoses, wiring, and anything else I didn't want covered in overspray.

Looking at the photographs, it almost appears that I've wrapped half the engine compartment in painter's tape.

But that's part of the process.

And with the original engine still at the machine shop, there was no better time to do it.

What started as an engine rebuild had gradually become an opportunity to restore practically everything surrounding the engine.

I'm beginning to think that dropping the engine from underneath wasn't such a bad idea after all.

A Fresh Coat of Burgundy — And Another Lesson from Bill

With the engine still out of the car, I finally reached another milestone: painting the engine bay.

After all the cleaning, rust removal, surface preparation, and masking, it was time to put some color back into the areas that had been looking pretty tired.

And not just any color.

The original Porsche M3V deep burgundy.

I applied the base coat, and what a difference it made. Areas that had been dull, scratched, and showing their age were beginning to look like they belonged on a properly restored Porsche again.

Of course, the job wasn't quite finished. I still needed to apply the clear coat.

That's when Bill asked me a question.

"Is your clear coat high heat?"

Well, no. I had purchased Eastwood's standard automotive clear coat, the type intended for exterior body panels. It hadn't occurred to me that the engine compartment might benefit from something different.

Bill explained his concern and offered to let me use the high-temperature clear coat he had at the shop.

Another lesson learned.

And then came lesson number two.

Bill reminded me that spraying clear coat in humid conditions isn't a particularly good idea. With the forecast calling for a 100% chance of rain the following day, we decided to wait a few days for better conditions.

As much as I wanted to finish the job, there was no sense rushing the final step after putting so much effort into the preparation.

One of the things I've come to appreciate about working with Bill is that he's willing to explain these details rather than simply telling me what to do.

I'm learning that getting a good finish isn't just about choosing the right color and spraying the paint. It's about selecting compatible materials, understanding the environment, and knowing when it's better to wait.

So, for now, the base coat is finished, and the clear coat will have to wait for a better day.

Forty-plus years of wear are disappearing, one project at a time. And apparently, I'm getting a little education in automotive painting along the way.

Another Call to Elliott

Of course, cleaning the engine bay also revealed a few more surprises.

Rust.

Some of it was in the passenger-side inner fender, and another area was around the battery-box drain opening. Both needed attention, and while I had considered fabricating patches from sheet metal, I thought there might be a better approach.

So, once again, I reached out to Elliott at 944 Barn.

As luck would have it, Elliott had recently picked up another 1984 Porsche 944 and was in the process of dismantling it.

A few days after our initial conversation, Elliott called me back to get a better understanding of exactly what I needed.

We exchanged photographs, discussed the rusted areas, and eventually identified the section of bodywork that would give me the metal needed for both repairs.

Elliott cut the entire section out of the donor car and sent me photographs of what he'd removed.

Perfect.

Rather than trying to fabricate the various curves, bends, and contours from scratch, I would have original Porsche sheet metal to work with. And better yet, it came from another 1984 944.

I'm planning to drive up to 944 Barn next week to pick up the entire section. Once I have it, I'll be able to determine exactly where to make the cuts and how best to fit the replacement pieces.

Of course, there's still the small matter of actually repairing the rust.

But at least I now have the material to work with.

One more problem solved—or at least one step closer. And once again, Elliott came through.

Stainless Steel Headers — Another Project Within the Project

While working through the various engine components, I had a conversation with Bill and Don about the exhaust headers.

My 1984 Porsche 944 originally came with the factory cast-iron exhaust manifolds, which I had every intention of keeping. In fact, I've set them aside and plan to have them professionally coated at some point. I like the idea of preserving the original parts, even if I decide to install something different.

Bill and Don suggested that I consider the later-style stainless steel tubular headers. Their reasoning was pretty straightforward: they look much cleaner in the engine bay and are considerably easier to install.

Of course, I called Elliott to get his opinion.

Elliott wasn't particularly enthusiastic about the idea. He warned me that the stainless steel headers were known to develop cracks, and he preferred sticking with the original equipment.

So now I had two different opinions from people whose experience I respect.

Naturally, I started searching.

After a bit of digging, I came across a set of stainless steel headers that had already been ceramic coated. The coating was a bronze color—not exactly what I had envisioned for the engine bay—but the headers themselves looked great.

After a little negotiating, I purchased them for $145 plus $25 shipping.

$170 for a ceramic-coated set of stainless steel headers. Not bad!

Unfortunately, the excitement didn't last long.

When the package arrived, I discovered that the seller's packaging left quite a bit to be desired. During shipping, a section of the ceramic coating had chipped off one of the header pipes.

I contacted the seller, expecting that we could work something out. Instead, he explained that he was going through a difficult time and selling off parts he had accumulated over the years. He wasn't willing to offer a refund for the damage, and the dispute became another issue I would have to sort out.

Not exactly the outcome I had hoped for, but I wasn't about to give up on the headers.

I brought them over to the shop and showed them to Bill. He suggested that, rather than trying to match the bronze coating, I should refinish the entire assembly in flat aluminum.

I liked that idea immediately. The aluminum finish would look much better against the freshly cleaned and painted components going back into the engine bay.

After some research, I found that VHT made a FlameProof primer and high-temperature paint in exactly the finish I wanted.

Before proceeding, I contacted VHT directly through Messenger to confirm that their primer could be applied over the existing ceramic coating. They provided specific application instructions, which I followed.

I prepared the headers, applied the primer, and finished them in VHT FlameProof Flat Aluminum.

Superscript

Then came the interesting part.

Baking the headers.

VHT specifies a staged heat-curing process:

  • 30 minutes at 250°F, followed by 30 minutes of cooling.

  • 30 minutes at 450°F, followed by another 30 minutes of cooling.

  • 30 minutes at 650°F for the final stage.

The first two stages were no problem. The third presented a slight complication: my oven doesn't reach 650°F!

So I completed the first two heating cycles and will finish the curing process after the headers are installed and exposed to operating temperatures, following VHT's guidance.

The transformation was remarkable.

What started as a bronze-colored set of headers with damaged ceramic coating now has a clean, uniform aluminum finish that should look fantastic when the engine goes back in.

And all of this began with a $170 eBay purchase.

Now, whether Elliott's warning about cracking proves correct remains to be seen. I'm hoping Bill and Don are right about the advantages of the later-style headers.

But just in case, those original cast-iron manifolds aren't going anywhere.

Sometimes the best restoration strategy is to improve what you have while keeping the original parts on the shelf.