THE FIRST WINTER PROJECT

One Project at a Time

What started as a few maintenance items turned into most of the engine bay coming apart.

By the first winter, I had become comfortable enough with the 944 to take on something considerably bigger. Rather than fixing one problem and putting the tools away, I decided to use the downtime to work through a long list of things that made sense to address together.

The cooling system got new water hoses. The fuel injectors came out for refurbishment, and I went through the fuel rail with new dampers. I specifically wanted the original Bosch components—not inexpensive knockoffs—and eventually tracked them down.

With the intake manifold removed, access opened up to parts of the engine that normally disappear beneath it. Old vacuum lines were replaced, and anything I could reasonably reach and refresh while I was there became part of the project.

Then the work migrated from the engine bay to underneath the dashboard.

Under the Dash

Sometimes the Hardest Part Is Reaching It

The brake booster was replaced, along with the clutch master and slave cylinders. The slave cylinder wasn't particularly memorable. The brake booster and clutch master cylinder were.

Working under the dashboard of a 944 isn't exactly an ergonomic experience. There were fasteners I could barely see, much less reach, and more than once I discovered that the tool I owned wasn't the tool I needed.

So I did what this project was increasingly teaching me to do: figure out the problem, buy the right tool, and try again.

Eventually the new booster and clutch hydraulics were installed. The intake went back on, the fuel system went back together, the hoses were connected, and after a winter of work, the 944 was ready to run again.

I turned the key.

Nothing.

THE TROUBLESHOOTING BEGINS

Now What?

After months of replacing parts that I knew needed attention, I suddenly had a problem I hadn't planned for: the car wouldn't start.

I reached out to two people who had already become valuable resources during the project: Bill at German Automotive and Elliott at 944 Barn. With their help, I started working through the usual no-start checklist.

DME relay. Spark. Tach bounce. Fuel. Reference sensors.

One item on that list brought me back to something I had encountered during the winter work. The electrical connector for the reference sensor had practically disintegrated when I touched it. At the time, I had repaired the connector and moved on.

Now, with an engine that wouldn't start, it suddenly seemed much more significant.

I decided to replace the reference sensor—and while I was in there, the speed sensor as well.

That sounded simple enough.

THREE WEEKS LATER

The Sensor That Wouldn't Come Out

Replacing two sensors should have been one of the easier jobs of the winter. One of them had other ideas.

The reference sensor wasn't the problem. The speed sensor was.

For nearly three weeks I tried different approaches, different tools and different ways of persuading it loose. Eventually the top of the sensor broke off. I was able to pull what remained of it up slightly and even get it to twist in the bracket, but without enough leverage—and with no real additional movement—it simply wasn't coming out.

Eventually, I stopped trying to save the bracket.

I cut it out.

To get enough room to work, I pulled the ignition wiring harness out of the way and went after the bracket. At the time, moving the harness seemed completely insignificant—just one more thing that had to be moved to get a tool where I needed it.

Elliott had a replacement bracket at 944 Barn, so I installed it along with a new reference sensor and speed sensor. After three weeks of fighting one stubborn part, everything was finally back together.

Surely that had been the problem.

I turned the key.

Still nothing.

THE BASICS FIRS

Forty Years of Resistance

Before digging deeper into the ignition system, Bill noticed two things he didn't like.

First was the starter.

Listening to the engine crank, Bill was convinced it simply wasn't turning the engine fast enough. The starter sounded tired—and after forty years, that wasn't exactly difficult to believe.

So I started searching.

I eventually found a brand-new starter in the UK for a surprisingly good price. Even more surprising, it was on my doorstep about five days later.

With the new starter installed, cranking improved—but Bill still wasn't completely satisfied with what he was seeing electrically. That shifted our attention to the cables carrying all that current.

From the outside, the original cables looked old, but not necessarily catastrophic. Once we started removing them, the real condition became obvious. The insulation was brittle and deteriorated, and one of the main cables was literally coming apart in our hands, exposing badly aged strands underneath.

At that point there wasn't much debate about whether they should stay.

We replaced the aging high-current wiring with heavy 0-gauge cable, made new connections and installed new battery terminals. It was probably overkill compared with what Porsche installed in 1984—but voltage drop through forty-year-old cables was one variable we would never have to chase again.

What forty years looks like inside a battery cable. Once removed, the condition of the original wiring made the decision easy. The insulation was failing and the conductor itself had badly deteriorated.
The original high-current wiring didn't look nearly as alarming while it was still installed. Getting it out told a different story.
New 0-gauge cable, new connections and new battery terminals completed the high-current side of the electrical system.

New starter.
New 0-gauge power and ground cables.
New battery connections.

The engine now cranked the way it should.

But it still wouldn't start.

So Bill went looking somewhere else.

WHEN THE BASICS CHECKED OUT

 Everything Said It Should Start / The Harness

I had run out of things I could reasonably diagnose in my garage. It was time to take the 944 back to Bill.

After weeks of chasing the no-start, the car went to German Automotive. Bill started with many of the same checks I had already worked through at home—but he had the equipment to actually measure what was happening rather than simply eliminating possibilities.

There was spark.

There was fuel pressure.

There was tach bounce while cranking.

And there was a pulse at the injectors.

Everything said the engine should start. It didn't.

We even went one step further and eliminated the DME. Elliott had a known-working unit at 944 Barn, so another $200 later we had one to test.

No change.

With the usual suspects eliminated, Bill turned his attention to the ignition wiring harness. Instead of replacing another part and hoping for the best, he began testing the harness wire by wire.

Eventually, he found it.

A broken wire.

And suddenly I remembered something.

During my three-week battle with the seized speed sensor, I had pulled the ignition harness out of the way so I could get enough room to cut the sensor bracket out. At the time, moving a 40-year-old wiring harness a few inches hadn't seemed particularly significant.

Now I had to wonder.

THE REPLACEMENT

$446 Later...

Finding the broken wire answered one question. Now I needed to decide what to do about a 40-year-old wiring harness.

Once Bill found the broken wire, I didn't spend much time debating whether to repair it. Before he even asked what I wanted to do, I had already started searching for a replacement ignition harness.

Finding one wasn't exactly cheap. $446 later, I had a new harness on the way.

When it arrived, I showed up at German Automotive and surprised Bill with it. Rather than simply handing him the part and waiting for the repair bill, Bill asked if I wanted to remove the air intake and fuel rail myself so he could get access to the existing harness.

Absolutely.

By this point, I had already had those parts off the car during the winter project, so the work was familiar—and doing it myself would save at least an hour of shop labor.

I came back the following Saturday, removed everything Bill needed out of the way, and left the 944 with him. About a week later, the replacement harness was installed.

Then it was my turn again.

I returned to the shop, put the intake and fuel system back together, checked everything over and finally reached the moment we'd been working toward.

We turned the key.

It started.

...and then it stopped.

ONE MORE QUESTION

But Was It Getting Fuel?

We had fuel pressure. We had injector pulse. The injectors had been professionally refurbished. What we didn't know was whether they were actually spraying.

That's where we tell the Rick-refurbished injector surprise, your spare Pull-A-Part set, the 944Online rebuild kit, Bill servicing them, and finally:

This time, it started—and kept running.

But it didn't sound right.