And as anyone who has ever taken apart an old car knows, removing one thing has a funny way of exposing three more things that suddenly need attention.
In my case, one of those things was the power steering rack.
Bill and Don removed the rack as part of dropping the engine, and its condition wasn't exactly a surprise. I already knew it was leaking. Power steering fluid had been collecting inside the right-side bellows and dripping out.
A few weeks earlier, Bill had suggested the straightforward solution: buy a professionally rebuilt rack.
The price?
$998.
There was a $325 core credit once I sent my old rack back, but still—that was a lot of money for something I couldn't help looking at and thinking:
Can I rebuild that myself?
By this point, Elliott had become one of my first calls whenever I was trying to figure out what made sense on a 944.
So I asked him:
“Have you ever rebuilt one of these racks?”
He had. A few times, actually.
His assessment wasn't particularly encouraging.
He'd had limited success rebuilding them, and his recommendation was simple: buy the rebuilt rack and be done with it.
I thought about that.
And then I thought about the donor engine.
I'd just gone through the exercise of replacing an original component with something that was supposed to solve my problem—only to discover that the replacement had problems of its own.
That made this decision considerably easier.
I was keeping my original rack.
And I was going to rebuild it myself.
944 Online had the seal kit. Rennbay had an excellent step-by-step video showing the disassembly and rebuild—including where the individual seals went, which direction they faced, and the order in which everything had to go back together.
And while I was there...
New inner tie rods.
New outer tie rods.
At this point, I had everything I needed.
Or at least I thought I had everything I needed.
Off I went.
With the rebuild kit from 944 Online, new inner and outer tie rods, and the Rennbay video as my guide, I started taking the original ZF rack apart.
As with most things on this car, the first few steps gave me a false sense of confidence.
The bellows came off. The hydraulic lines were removed. I documented where everything went, took plenty of pictures, and laid the pieces out as they came apart.
Then I got deeper into the rack.
This wasn't like rebuilding a brake caliper. There were seals buried inside the housing, components that had to come apart in a particular order, and parts that required tools I didn't own.
One of the first challenges was the large threaded collar inside the rack housing.
It had two holes in its face and clearly required some type of pin spanner.
Easy enough.
I found a variable pin spanner at Harbor Freight that looked like it should do exactly what I needed.
It didn't.
The pins protruded too far from the face of the tool. That prevented the spanner from sitting flat against the rack tube, which meant I couldn't get the pins properly seated in the collar.
Another tool purchased.
Another tool that wasn't going to solve the problem.
And another reminder that on a 42-year-old Porsche, “the right kind of tool” and “the right tool” aren't necessarily the same thing.


I had the removal tool. It slipped over the tie rod, and an insert engaged the flats so I could use a breaker bar. The problem wasn't the tool.
The problem was the rack.
With the rack out of the car, I had nothing solid to work against. One hand was trying to hold the rack while the other was trying to operate the tool. The rack moved before the tie rod did.
There was another complication. Porsche—or ZF—had made sure the tie rods weren't going anywhere. The edge of the tie rod had been notched/staked into the rack, mechanically locking it in place. I had already started knocking the staked metal back, but with the rack moving around it was difficult to get a clean hit.
Looking around the garage, I noticed some scrap 6x6 landscape timbers left over from another project. One was about 24 inches long.
That might work.
I used the rack's original mounting brackets to screw the entire steering rack directly to the 6x6.
It was almost comically simple, but it completely changed the job.
The combination of the timber's weight and stability created a solid base. Now I could give the locking notches a few more tap... taps and knock the staked steel back far enough to release the tie rods.
More importantly, I wasn't using one hand to chase the steering rack around the workbench anymore.
With the rack stable, I could finally put both hands on the removal tool and apply the torque I needed.
The inner tie rods came off.
Sometimes the solution isn't another specialty tool.
Sometimes it's a leftover piece of 6x6.
It had two notches in its face, and just like the tie rods, it wasn't simply threaded in place. The aluminum housing had been notched over to prevent the collar from rotating.
So, first things first: a few more careful tap... taps to knock the aluminum back and free the collar.
Now I just needed to unscrew it.
My first attempt was a screwdriver.
Bad idea.
The sharp edge of the screwdriver immediately started damaging the collar. I stopped before I made things worse.
Next came several other attempts, including a variable pin spanner from Harbor Freight. It looked like exactly the tool I needed. In reality, the pins protruded too far, preventing the tool from sitting flat against the rack housing and properly engaging the collar.
Nothing worked.
Then I found the tool.
It wasn't from Porsche.
It wasn't from Harbor Freight.
It wasn't even an automotive tool.
It came with the bed frame in our bedroom.
It was one of those little assembly tools manufacturers throw into the box with furniture—an Allen-wrench-style head with a short, flat handle.
And it was nearly perfect.
The flat end fit into the notch on the collar without the sharp edge of the screwdriver, and the short handle gave me enough control to hold it firmly in position while tapping it with a hammer.
So I started carefully.
Tap... tap.
Nothing.
Tap... tap.
Still nothing.
At some point I decided:
Enough is enough.
I held the little bed-frame tool firmly against the notch (pointing in the direction of intended rotation) and gave it one good, hard TAP.
The collar moved.
Finally.
From there, it became a rhythm. Tap the collar around a little. Move the tool to the other notch. Tap again. Switch back. Keep alternating between the two notches as the collar slowly rotated out of the housing.
And eventually...
the collar was free.
I had tried a screwdriver, a purpose-built pin spanner and several other tools.
The winner?
The free Allen-wrench thing that came with our bed.
Once this seal came out, I could officially call the steering rack disassembled.
The other seals had actually been pretty easy. Because I could get to them from the backside, the formula was simple: find the right-size socket, add an extension, give it a few taps with a hammer, and out they came.
But the final seal sat at the bottom of the main housing.
There was no easy way to get behind it.
So, back to the Internet. Back to YouTube.
Eventually, I stumbled across a video where a guy used an extra-long pair of 90-degree needle-nose pliers. He fed them into the housing from the side and positioned the tips underneath the seal. From there, he could push upward against the backside and work the seal out.
Perfect.
Except, of course, I didn't own an extra-long pair of 90-degree needle-nose pliers.
I was heading down to see Bill at the garage anyway, so I decided to bring the rack with me. Bill has been working on these cars for something like 40 years and is always talking about the little tricks you learn after doing this stuff long enough.
Maybe he had one for this.
I walked into his office carrying the rack.
“I have a question and a favor.”
I showed him the seal and explained the problem.
He looked at it.
“Follow me.”
We walked back into the garage and Bill started digging through his toolbox.
I was expecting some obscure seal puller or one of those homemade tools that mechanics keep around for decades because it solves exactly one problem.
Instead, the next thing I knew, Bill was standing there with...
a hammer and a small chisel.
And I'm thinking:
What the hell?
He's going to gouge the aluminum housing. This is going to be exactly where the rack leaks after I put the whole thing back together.
But this was also the guy who had been working on these cars for 40 years.
So I watched.
A minute later, the seal was out.
Was it quite as clean and delicate as I would have liked?
No.
Was the seal out?
Yes.
And that was all that mattered.
After all the searching, videos, specialty tools and improvised solutions, the final obstacle came down to something incredibly simple:
experience, a small chisel and a hammer.
The steering rack was finally completely disassembled.
Now I could clean everything one last time, lay out the new seals and start putting it all back together.
And, of course, that's when I would discover that taking a 42-year-old steering rack apart and putting one back together are two very different things.
With the rack completely apart, everything got another thorough cleaning—including the external tubes. After everything it had taken to get the rack apart, I really didn't want dirt or old fluid becoming the reason I had to do this again.
For the reassembly, I went back to the Rennbay video and started exactly where they did: the main seals.
I paid close attention to the orientation of each seal, found a socket that fit nicely over the outside edge, and carefully tapped the first one into place. The video suggested checking the Teflon ring underneath for any movement once the seal was installed. If there was play, the seal wasn't completely seated.
Mine felt solid.
Good. Because after all of this, the last thing I wanted was a power-steering leak.
Next came the pinion. I replaced the rubber and silicone rings, again paying attention to their locations and orientation.
So far, everything was going exactly according to plan.
Then came the rack shaft. Following the order from the rebuild instructions, I worked my way through the stack:
securing ring → Teflon spacer → two rubber rings in the groove → larger ring over the rubber rings → rubber and Teflon rings around the outer edge of the larger ring → Teflon ring → final securing ring.
Everything went back together without a problem.
This was almost getting easy.
With the pinion rebuilt and sitting there, I had a thought that seemed perfectly reasonable at the time:
Why not slide it into the housing just to make sure everything fits?
So I did.
It slid right in.
Perfect fit.
And then I realized what I'd just done.
The pinion wasn't supposed to go in yet.
The rack shaft had to go in first.
No problem. I had just slid it in. I'd just pull it back out.
Except it wasn't coming back out.
I pulled a little harder.
Still nothing.
A little harder...
And then it came out.
Unfortunately, so did the realization of what had been holding it in place. The last silicone ring had caught inside the housing as I pulled the pinion back out—and broke.
I looked through the rebuild kit.
No spare.
Of course there wasn't.
I still had the original rings I'd removed, and fortunately they actually looked pretty good. The underlying rubber ring wasn't damaged either, so I inspected the four old silicone rings, picked the best one, and put it back onto the pinion.
Not exactly the plan, but we were back in business.
And this time, the pinion stayed on the bench until it was actually supposed to go in.
Next, it was a good thing I had taken plenty of pictures before taking everything apart.
I had a pretty good sense of where the rack shaft had been positioned and, more importantly, how the pinion needed to go back in so I could keep everything aligned the same way it had been when I started.
From my pictures, I had a reference point I could actually reproduce:
13 teeth showing on the driver's side meant the flat side of the upper steering connection shaft was facing the passenger side of the rack.
That became my alignment mark.
I positioned the rack shaft with the same 13 teeth exposed and started lowering the pinion into place.
Of course, it wasn't quite as simple as lining it up and pushing it straight down. As the pinion gear engages the rack, the angled teeth cause the pinion to rotate slightly as it slides into position. It took me a few tries—pull it back up, move it a tooth, try again—before I found the right starting tooth.
Eventually, it dropped into place with the rack still showing my 13-tooth reference and the flat on the upper shaft ending up where it belonged: toward the passenger side.
That was exactly what I was looking for.
And this time, unlike my earlier "test fit," the pinion was supposed to stay there.
With the rack shaft and pinion finally aligned, I was feeling pretty good about the reassembly.
Then I looked down at the workbench.
One rubber ring was still sitting there.
That's generally not what you want to see when you're rebuilding a steering rack.
I went back through the instructions and looked over the housing trying to figure out what I had missed. On the side of the aluminum housing was a small plate held in place by two screws. Behind the plate was a spring and a plastic component.
Looking at the leftover rubber ring, I thought I had found the answer.
It appeared to be almost exactly the right diameter to fit around the spring and beneath the cover plate. And I couldn't see any other obvious sealing surface that would prevent power-steering fluid from leaking around that plate.
That had to be it.
I fitted the rubber ring around the spring, reinstalled the plate and tightened everything back down.
Then I tried turning the pinion.
Something was wrong.
There was suddenly considerably more resistance—enough that the pinion almost didn't want to turn at all.
That wasn't how the rack had felt moments earlier.
Rather than assuming the new seals were simply tight and forcing it, I went back to the last thing I had changed.
Off came the plate.
Out came the rubber ring.
I tried the pinion again.
Smooth.
Okay. Apparently that wasn't where the ring belonged.
I still didn't know where it went, but I knew where it didn't go.
So I put the mystery ring aside.
I didn't throw it away.
Just in case.
From there, the rest of the rebuild was surprisingly uneventful.
I brought my trusty 6x6 landscape timber back into service, mounted the rack to it again and used the stable base to reinstall the threaded retaining collar and torque the new inner tie rods into place.
The same scrap piece of wood that helped me get everything apart was now helping me put it all back together.
The new bellows went on, followed by the outer tie rods.
I knew the final position of the outer tie rods would ultimately be set once the rack was back in the car and the 944 received a proper wheel alignment. But I still wanted everything reasonably close before installation.
Once again, those pictures I had taken before disassembly proved their value.
I went back to the original photographs, counted the exposed threads on each side and used those measurements to position the new outer tie rods approximately where the originals had been.
It wouldn't replace an alignment.
But it should get me close enough to get there.
And with that, the original ZF steering rack was back together.
New seals.
New inner tie rods.
New outer tie rods.
New bellows.
And, most importantly, it was still my original rack.
A few weeks earlier, I had been considering spending nearly $1,000 on a rebuilt replacement and sending this one away as a $325 core.
Instead, I kept it, took it completely apart, figured out every obstacle it threw at me, and rebuilt it myself.
Would it leak when everything was finally back in the car and filled with fluid?
There was really only one way to find out.
But for now, I was calling this one done.

